Post by Luxington on Sept 22, 2008 16:47:20 GMT -5
*copied from a wow guildie of mine* All praise be to vonbimini
Vent Normalization makes every bodies voice the exact same volume. In essence, you won't blow your ear's out or have difficulty hearing people.
____________________
Here's how:
- Go to Setup
- Enable Direct Sound
- Select the SFX Button
- Select Compressor and click Add.
- Under Compressor Properties use the following settings
- Gain = Adjust for how loud you want people to be. (I use 15)
- Attack = 0.01
- Release = Around 500
- Threshold = Around -30
- Ratio = 100
- Pre delay = 4.0
Edit:
What the settings do - Copied and pasted from page 8
Gain
How much volume you feed into the compressor. Not really relevant unless everyone is too quiet, then you can turn this up a little; turning it up too much will sound EXTREMELY *%*%ty.
Attack
How fast volume change will happen. example: setting this to 500 means that any-
thing coming in will only be dropped in volume after a half a second. for vent this should
be set as low as possible.
Release
how fast the compressor stops changing things. not really that relevant with vent, setting it around 500 is good for voice material.
Threshold
This sets the point where we actually start changing what�s coming in. Whereas 0 is the absolute loudest you can have for an input, -60 is super quiet. Average users will probably come in somewhere around -25 to -15, with the occaisional few being really quiet, which is why I have this set so low.
Ratio
How much any sound below the set threshold gets compressed and/or modified in the volume department.
If you still want to hear SOME volume variation then set this lower (2-4)... the higher you set it the closer in volume everyone will be.
Pre delay
Mostly just deals with processing; with computer and digital processors they can look ahead a few milliseconds to see what needs to be dropped in volume or changed before it actually comes through the speakers. Highest is ideal.
Vent Normalization makes every bodies voice the exact same volume. In essence, you won't blow your ear's out or have difficulty hearing people.
____________________
Here's how:
- Go to Setup
- Enable Direct Sound
- Select the SFX Button
- Select Compressor and click Add.
- Under Compressor Properties use the following settings
- Gain = Adjust for how loud you want people to be. (I use 15)
- Attack = 0.01
- Release = Around 500
- Threshold = Around -30
- Ratio = 100
- Pre delay = 4.0
Edit:
What the settings do - Copied and pasted from page 8
Gain
How much volume you feed into the compressor. Not really relevant unless everyone is too quiet, then you can turn this up a little; turning it up too much will sound EXTREMELY *%*%ty.
Attack
How fast volume change will happen. example: setting this to 500 means that any-
thing coming in will only be dropped in volume after a half a second. for vent this should
be set as low as possible.
Release
how fast the compressor stops changing things. not really that relevant with vent, setting it around 500 is good for voice material.
Threshold
This sets the point where we actually start changing what�s coming in. Whereas 0 is the absolute loudest you can have for an input, -60 is super quiet. Average users will probably come in somewhere around -25 to -15, with the occaisional few being really quiet, which is why I have this set so low.
Ratio
How much any sound below the set threshold gets compressed and/or modified in the volume department.
If you still want to hear SOME volume variation then set this lower (2-4)... the higher you set it the closer in volume everyone will be.
Pre delay
Mostly just deals with processing; with computer and digital processors they can look ahead a few milliseconds to see what needs to be dropped in volume or changed before it actually comes through the speakers. Highest is ideal.
funny thing is, I hadn't set mine up yet. 
And aye, i shall use the search next time, i was just excited about being needed and wanted 